HEPA filtration, not standard vacuums
A standard vacuum passes fine drywall dust straight through its filter and back into the air. HEPA filtration is what actually removes it rather than relocating it.
Serving Burnsville, Minnesota & surrounding areas
Mon–Fri 8am–6pm · Sat 9am–2pm
Services
Commercial Cleaning Services Janitorial Services Industrial Cleaning Services Floor Care Services Deep Cleaning Services Post-Construction Cleaning Services Window Cleaning Services Carpet Cleaning House Cleaning ServicesIndustries
Restaurant Cleaning Office Cleaning Medical Facility Cleaning Retail & Shopping Center Cleaning School & Daycare Cleaning Financial Institution Cleaning Auto Dealership Cleaning Salon & Spa Cleaning Fitness Center & Gym CleaningAreas Served
Bloomington Lakeville Eagan Eden Prairie Apple Valley Edina ContactRough, final, and touch-up cleaning for finished builds and remodels, handling the fine drywall dust and installation residue that ordinary cleaning cannot remove.
Drywall dust is the reason post-construction cleaning exists as a separate service. It is far finer than household dust, it is faintly abrasive, it carries a static charge that makes it cling to vertical surfaces, and it settles into every track, channel, and gap a building has. A standard clean pushes it around. Twenty minutes later it has resettled and the room looks exactly as it did before.
Burnsville Cleaning handles finished construction and remodel cleanup in the sequence the work actually requires: contain and remove the bulk, work top-down through every surface with HEPA filtration and controlled wiping, then repeat where dust has resettled. It usually takes more than one pass, and pretending otherwise just moves the problem to the client.
Timing is the other half of the job. A final clean run before the trades have genuinely finished is money spent twice, because one more cut, sanding pass, or fixture install puts dust straight back into a cleaned space. We schedule against your punch list rather than against a hopeful date.
Post-construction cleaning is normally split into phases, and which ones you need depends on how far along the project is and what your contractor has already handled.
The phases and what each one covers:
Tell us which phases your contractor is covering and which are ours. Overlapping scopes waste your money, and gaps between them show up on handover day.
A standard vacuum passes fine drywall dust straight through its filter and back into the air. HEPA filtration is what actually removes it rather than relocating it.
Dust settles for hours after disturbance, so a single pass always leaves a film. Planning for a second pass is the difference between clean and briefly clean.
Window tracks, door channels, hinge gaps, cabinet runners, and vent louvers hold dust that reappears the moment anything moves. They need deliberate individual attention.
Adhesive, paint, grout haze, and joint compound each need a different method. The wrong solvent or blade on a new surface causes damage that is immediately visible.
Fresh paint, new fixtures, uncured caulk, and unfinished floors all mark easily. Crews working in a new build need to know what not to touch as much as what to clean.
Cleaning before the trades are finished means paying for the same clean twice. We schedule against punch list completion, not against an optimistic target date.
We walk the site, assess how much dust and debris is present, identify delicate new finishes, and confirm which phases you need from us rather than assuming all of them.
We agree in writing who handles debris disposal, who removes floor protection, and where your contractor's cleanup ends and ours begins, so nothing is double-billed or missed.
If a rough clean is in scope, we clear debris and packaging first so the detailed work is not being done around obstacles that should already be gone.
The detailed pass works from ceilings and high surfaces down through fixtures, glass, tracks, cabinetry, and finally floors, using HEPA vacuums and controlled wiping to remove dust rather than spread it.
Once punch list work is finished, a touch-up pass clears the dust that construction corrections inevitably created, so the space is genuinely ready on handover day.
Post-construction cleaning in Burnsville typically runs about $0.25 to $0.75 per square foot for a final clean, putting most residential remodels in the range of roughly $400 to $1,500 and new-build or larger commercial projects higher. Rough cleans and touch-up passes are usually priced separately, either per square foot or as hourly work depending on scope.
Cost depends on how much dust and debris is present, how many phases you need, the amount of adhesive and residue removal involved, window count, ceiling height and whether high work needs lift access, and how tight the handover deadline is. We quote after a site visit, because construction cleanup estimated from a floor plan is guesswork.
If your build is nearly finished and the dust is still winning, get a site visit and a phased cleaning plan timed to your actual handover date.
Request a CallbackAfter all trades have genuinely finished, including punch list corrections and final fixture installs. A final clean run while any cutting, sanding, or drilling remains will be undone, because fine dust redistributes across every cleaned surface within hours. We usually recommend the detailed pass once the site is closed to trades, plus a short touch-up immediately before handover.
Mostly equipment. Standard vacuums pass fine drywall dust straight through the filter and exhaust it back into the room, so the dust moves rather than leaves. Construction cleanup also involves adhesive removal, grout haze, paint specks, and residue work that ordinary cleaning does not cover, and it requires knowing which new finishes will mark if handled incorrectly.
We remove packaging, offcuts, and general debris as part of a rough clean, and we can bag and stage material for your dumpster. Large-volume disposal, hazardous material, and anything requiring a permitted hauler is normally the contractor's responsibility, and we confirm that division of work in writing before starting.
Usually at least two. Dust continues settling for hours after it is disturbed, so a single pass always leaves a visible film on horizontal surfaces. We plan the detailed clean and then a follow-up or touch-up pass. Anyone promising a one-visit result on a dusty site is either doing rough work or will be back.
Yes. On longer projects, scheduled interim cleans keep debris and dust under control so trades can work efficiently and safely. It does not replace the final clean, but it makes the final clean faster and reduces the amount of dust that has worked its way into tracks and finishes.
Yes, and construction glass needs particular care. Sills and tracks collect heavy dust and often hold paint specks, adhesive, or compound splatter that has to come off without scratching new glass or damaging frames. We cover interior glass as part of a final clean, and exterior glass can be included when weather allows.
In practice, yes. A remodel is dirtier in a specific way, because dust migrates into occupied parts of the building through HVAC and doorways, so protection and cleanup extend beyond the work area itself. A new build has more total dust but it stays contained within an empty structure, which usually makes it more straightforward to work through systematically.
Tell us the project size, which phases you need, and your target handover date. We will visit the site, agree the scope split with your contractor, and schedule the cleaning so the space is ready when you need it.
Request a Quote
Send the details and we will come out for a walkthrough, then put a written scope and price in front of you.